BLACK
HPRC 3500 Case - Empty
Description
HPRC 3500 EMPTY CASE - NO FOAM
O.D. 14.57" x 19.61" x 7.28"
I.D. 12.63" x 17.06" x 6.31"
The 3500 Backpack is an injection-molded backpack that is watertight, airtight and virtually crushproof. It is made of TTX01 polypropylene plastic resin with a micro-textured surface to reduce scratching. It can be customizable with a cubed foam, with an interior nylon bag or can be purchased empty.
The ergonomic back pad is made of fast drying antibacterial foam and was designed to be thicker in critical areas such as the shoulder blades and lumbar to provide the precise level of required support and protection. The adjustable shoulder and side straps are made of soft air mesh to allow for comfort and quick moisture evaporation. Four extra strong side loops have been molded in for attaching future accessories such as a jacket and helmet net as well as a tripod holder.
Pack Basics
- Injection molded shell made of advanced patented plastic, TTX01 polypropylene-resin, for up to 20% lighter weight
- Micro-textured surface to reduce scratching
- Neoprene O-ring to keep the case air and watertight
- Air pressure release valve included
- Double-hinge locking latches for secure close and comfort open
- Four extra strong side loops have been molded in for attaching future accessories such as a jacket and helmet net as well as a tripod holder
Certifications
- ATA (Air Transport Association) 300 rated
- IP67 Military specification for protection against dust and against the effect of immersion between 15cm and 1.0 m
- STANAG 4280 is a NATO specification for high and low temperatures for extended periods of time (up to 131° Fahrenheit for 48 hours and as low as -4.0° Fahrenheit for 16 hours)
- DS 81-41 (military-grade)
Choose from the following colors at checkout
BLACK
Need Custom Foam?
Design it yourself
Use the MyCaseBuilder App to design the perfect custom foam insert yourself.
Start designing >
Specifications
Inside Dimensions
Length:
12.625" (321mm)
Width:
17.0625" (433mm)
Base Depth:
3.8125" (97mm)
Lid Depth:
2.5" (64mm)
Total Depth:
6.3125" (160mm)
Corner Radius:
1.5" (38mm)
Outside Dimensions
Length (O.D.):
14.57" (370mm)
Width (O.D.):
19.61" (498mm)
Total Depth (O.D.):
7.28" (185mm)
Case Information
Case Type:
Injection Molded
Durability:
Heavy Duty
Empty Weight:
6.61 lbs (3.00kg)
Handle:
Foldable
Latch Type:
Up and over pull down
Lockable:
Padlockable
Made in the U.S.A.:
No, Made in Italy
Pressure Relief Valve:
Yes
TSA Approved
:
TSA requires the following:
- The firearm must be in a hard-sided container.
- The container must be locked. A locked container is defined as one that completely secures the firearm from being accessed. Locked cases that can be pulled open with little effort cannot be brought aboard the aircraft.
Please refer to the TSA website for more information:
TSA Transporting Firearms and Ammunition
Yes, Airline approved
Wall Construction:
Single Wall-Injection Molded
Waterproof
Waterproof: Yes - IP67 Rated 100% protected from dust and sand and can be submerged up to 3 feet of water for up to 30 minutes
Weather resistant - Can withstand spashes of water but cannot be submerged
:
Weather resistant - Can withstand spashes of water but cannot be submerged
Yes
Wheels:
No Wheels
Custom Foam Information
With MyCaseBuilder, you are designing full replacement foam for the base of your case.
When you receive your foam it will be the full height and slip right into the base of your case.
If you have a case already and only need replacement foam, you will have the choice to add lid foam during checkout.